Deys Betontechniek B.V.

Giet- en ondersabelingsmortels,Betonreparatie producten, Injectieproducten, Kunststoffen, Mortelpompen, Voegovergang constructies

Deys Targets
  • Chemical-and petrochemical plants

  • Delta works

  • Sea Lock IJmuiden

  • Harbours

  • Industry

  • Offshore

  • Powerplants

  • Department of public works

  • Railways

  • Utility

  • Airports

  • Water treatment

  • Road and water construction

  • windmills




BETEC MULTIFLOW 600 0-5 R is a so-called non- (wet) shrinking moulding mortars based on Portland cement which are applied in the heavy and medium-heavy industry as well as in road and hydraulic engineering .

Type Grain structure  
600 0 – 5  
Quality control

During manufacturing only high-quality aggregates are used, which meet the strictest requirements. During the production process as well as during the final stages these materials are extensively tested for quality, not only in our own laboratory, but also in independent acknowledged institutes.

Application areas Advantages
  • Grouting of big constructions with heavy static and/or dynamic load, like foundations of machines, railway constructions, concrete constructions and joint junctions
  • Fastening reinforcement bars and anchors as well as grouting holes in concrete structures
  • Injecting gain holes in columns and joints in prefab concrete structures
  • Products ready for use, which are easy to process and environment-friendly
  • Chromate reduced
  • Checked volume increase
  • No plastic shrinkage/ very low hydratation heat development
  • Extremely fluid
  • Very high early and final strengths
  • Resistant to frost and gritting materials, like salt
  • Minimal desiccation shrinkage
  • Free of chlorides and other corrosive aggregates
  • Contain no aluminous cement
  • Thickness of layer 20 – 600 mm !
  • Can be pumped, vibrated or poured without any danger of de-mixing
Packaging and storage
25 kg bags. Dry and frostproof, storage life 12 months in the original and closed packaging.
Refer to safety data sheets
Article number Multiflow 600
Kind of mortar Grouting mortar
Type of mortar (mm) 5
Thickness of layer (mm) 20-600
Class of strength K70
Environmental degree x0 t/m xa3
Water penetration (mm) < 10
Resistance tof rost and gritting materials (salt) < 0.4
Carbonatation depth (91 days) (mm) < 2
Halogen content (%) < 0.05
Thermic expansion coefficient (ºC) < 15 x 10-6
Polymer irrelevant
Volume increase [%] > 0.1 and
Yield measurement [mm]  
 • after 5 minutes > 680
Desiccation shrinkage 0.23
(measument of shrinkage in experimental patches that received no curing)  
Water segregation (bleeding) none
Min. Processing temperature [°C]* 5
Max. Processing temperature [°C] 35
Relative humidity foundation soil Moderately damp
Bond strenght to concrete [N/mm²] > 2
Water dosage Refer to front of package
Air content [%] approx 5.0
E-module [N/mm²] 32000
Calculation of amount of dry mortar [kg/m³] 2,0
Density of mixed mortar [kg/dm³] 2.3
Compressive strength [N/mm²] (20°C)  
 • 4 hours 28
 • 1 day 38
 • 7 days 73
 • 28 days 80
Flexural-tensile strength [N/mm²] (°C)  
 • 1 day 6
 • 7 days 8
 • 28 days 10
Complies with CUR recommendation 24 and 54 **At temperatures below 5 ºC measures for winter conditions must be taken (material applicable till -5ºC) Processing time max. 30-45 minutes


The technical instructions and recommendations we provide on the basis of our experience and to the best of our knowledge, are entirely without obligation and merely provide an indication. Not all facts, problems and queries that occur during practical application can be included in a general documentation sheet. Our recommendations and instructions do not commit us to any legal obligations as a result of the purchase and application of our products. Any deviating agreements made by our employees that are not included in our datasheets will only be lawful providing they have been confirmed in writing by the management. Our raw materials, semi-finished products and products comply with the most stringent quality standards. This does not relieve the user of their responsibility to test our products prior to their application. Our general trading and delivery conditions, which we are happy to forward to you on demand, are and remain applicable at all times.
This specification sheet supersedes any previous versions.