BETOCHEM 3000
Description |
---|
BETOCHEM 3000 moulding mortar is a high-fluidity grouting mortar free of solvents based on epoxy resin and laminar fillers. After only a short time.BETOCHEM 3000 moulding mortar has a high tensile strength. The moulding mortar hardens through well at low temperatures and is slightly exothermic. BETOCHEM 3000 can also been supplied as a RAPID version. BETOCHEM 3000 OW can also been used under water |
Quality control |
---|
During manufacturing only raw materials of high quality are used which amply meet the strictest requirements. During the production process as well as during the final stages these materials are extensively tested for quality in our own laboratory. |
Application areas |
---|
|
Packaging and storage |
---|
20, 30 and 40 kg. In the original properly closed packaging in a cool dry place, frost free minimum storage life 6 months. |
Precautions |
---|
Refer to the information on the packaging of the product, safety sheets and processing advice C. |
Application |
---|
By means of moulding. Tools can be cleaned with BETOCHEM brush dilutant EP. |
Ground |
---|
Concrete cement-bound, stone-like and metal grounds. The ground should be clean, dry (not for OW system) and free of dust, grease and dirt and furthermore should meet the terms and conditions that normally apply. Free metal grounds of corrosion products and a primer should be applied if so required. |
Resistance to chemicals |
---|
Refer to list of resistance to chemicals. |
Article Code (also OW system) | 3000 Fine | 3000 Medium | 3000 Coarse |
---|---|---|---|
Type | F | M | G |
Thickness of layer [mm] | 0-30 | 20-60 | 50-100 |
Set packaging (kg) | 20 | 30 | 40 |
Colour | grey (RAL clour on demand) | ||
Density [kg/dm³](20°C) | 1.8 - 2.1 | ||
Amount to be used (kg/m²)(at 1 cm thickness of layer) | 18-21 | ||
Solid content (percentage by volume) | 100 | ||
Mixing ratio (by part of weight) | |||
• Component A | 92 | ||
• Component B | 8 | ||
Component C (kg) | 10 | 20 | |
Flash point [°C](DIN 53213) | |||
• Component A | > 100 | ||
• Component B | > 100 | ||
Potlife(h) (25°C) | approx. 1 | ||
Processing temperature [°C] | 8-35 | ||
Drying/full-hardening (20°C/65% RH/3 cm thickness of layer) | |||
• dust-dry | after approx. 4 hours | ||
• repaintable | after approx.16 hours | ||
• ready to walk on | after approx. 16 hours | ||
The RAPID conversion has a compressive strenght | after 3 hours 20N/mm2 after 4 hours 40N/mm2 | ||
(in system building or with several layers, a maximum drying time of 24 hours between layers applies, unless a pre-treatment of the surface has occured) | |||
(thickness of layer depends on fraction enclosed, in case of application of layers thicker than advised, because of exothermic reaction during cooling thermic shrinkage may occur it is suggested to apply thicker layers in several layers) | |||
Compressive strength [N/mm²] | +/- 100 | ||
Flexural-tensile strength [N/mm²](20°C) | 40 | ||
E-module [N/mm²] | 11.000 | ||
Shear strength [N/mm²] | 35 (blasted steel) | ||
Tensile strength [N/mm²] | 18 | ||
Linear expansion coefficient (5K1) | 5 x 10 | ||
Exothermic behaviour [°C] | approx. 15 above processing temperature | ||
H.D.T. [°C] | 70 |
" Can also be supplied as a winter/rapid version to be used for temperatures from 2 °C, ask our tecnical service.
Safety sheets |
---|
Download: Betochem 3000 RAPID A-comp_EN |
Download: Betochem 3000 RAPID B-comp_EN |
Download: Betochem Cleaner EN |
Please contact us, we will send you the information. |
Liability
The technical instructions and recommendations we provide on the basis of our experience and to the best of our knowledge, are entirely without obligation and merely provide an indication. Not all facts, problems and queries that occur during practical application can be included in a general documentation sheet. Our recommendations and instructions do not commit us to any legal obligations as a result of the purchase and application of our products. Any deviating agreements made by our employees that are not included in our datasheets will only be lawful providing they have been confirmed in writing by the management. Our raw materials, semi-finished products and products comply with the most stringent quality standards. This does not relieve the user of their responsibility to test our products prior to their application. Our general trading and delivery conditions, which we are happy to forward to you on demand, are and remain applicable at all times.
This specification sheet supersedes any previous versions.