Deys Betontechniek B.V.

Giet- en ondersabelingsmortels,Betonreparatie producten, Injectieproducten, Kunststoffen, Mortelpompen, Voegovergang constructies

Deys Targets
  • Chemical-and petrochemical plants

  • Delta works

  • Harbours

  • Industry

  • Offshore

  • Powerplants

  • Department of public works

  • Railways

  • Utility

  • Airports

  • Water treatment

  • Road and water construction

  • windmills

    Windturbines

BETOCHEM 3200

Description

BETOCHEM 3200 extra fine is a two-component levelling mortar free of solvents based on high-grade epoxy resin.
BETOCHEM 3200 extra fine levelling mortar has a high tensile strength after only a short time. The mortar hardens through well at low temperatures and is slightly exothermic.
BETOCHEM 3200 extra fine is not susceptible to hardening shrinkage and is highly resistant to chemicals.

Quality control

During manufacturing only raw materials of high quality are used which amply meet the strictest requirements. During the production process as well as during the final stages these materials are extensively tested for quality in our own laboratory.

Application areas
  • BETOCHEM 3200 extra fine is the ideal mortar for constructions which are exposed to vibrations and/or chemical strain. Because of the non-exothermic characteristics the material is highly applicable in the chemical and petrochemical industry.
  • Levelling and gluing profiles, bearing blocks on rubber,steel and concrete
  • Protection of  concrete reinforcement
Packaging and storage
5 kg – In the original properly closed packaging in a cool dry place, frost free minimum storage life 12 months.
Precautions
Refer to the information on the packaging of the product, safety sheets and processing advice C.
Application
By means of a trowel etc. For thixotroping the material BETOCHEM thickener can be added; dosage depends on the application, but will generally amount to 50 gram per 5 kg set. Thickener is added when the layer thickness is 10 mm, depending on the temperature. Tools can be cleaned with BETOCHEM brush dilutant EP.
Ground
Concrete, other cement-bound and stone-like grounds and steel. The ground should be clean, dry and free of dust, grease and dirt and furthermore should meet the terms and conditions that normally apply. Metal grounds should be freed of corrosion products and a primer should be applied if so required.
Resistance to chemicals
Refer to list of resistance to chemicals.
Article Code 3200 extra fine
Colour concrete grey (RAL colour on demand)
Density [kg/dm³](20°C) 1.9
Amount to be used (kg/m²)(1 cm thickness of layer) 22
Thickness of layer (cm) 5 at the maximum
Solid content (percentage by volume) 100
Mixing ratio (by part of weight)  
 • Component A 92.2
 • Component B 7.8
Flash point [°C](DIN 53213)  
 • Component A > 100
 • Component B > 100
Potlife [h] (20°C) approx. 1
Processing temperature [°C] 5-35
Drying/full-hardening (20°C/65% RH/3 cm thickness of layer)  
dust-dry after approx. 4 hours
repaintable after approx. 16 hours
ready to be walked on after approx. 16 hours
(in system building or with several layers, a maximum drying time of 24 hours between layers applies, unless a pre-treatment of the surface has occured)  
Compressive strength [N/mm²] 28 days 85
After 1 day [N/mm2] 45
After 7 days [N/mm2] 80
Flexural-tensile strength [N/mm²](20°C) 45
E-module [N/mm²] 2950
Shear strength [N/mm²] 30
Tensile strength [N/mm²] 16
Linear expansion coefficient (5K1) 3.5 x 10
Exothermic behaviour [°C] approx. 15 above processing temperature
H.D.T. [°C] 70
Processing advice
General Processing Advice Synthetic materials [C]
Please contact us, we will send you the information.

Liability

The technical instructions and recommendations we provide on the basis of our experience and to the best of our knowledge, are entirely without obligation and merely provide an indication. Not all facts, problems and queries that occur during practical application can be included in a general documentation sheet. Our recommendations and instructions do not commit us to any legal obligations as a result of the purchase and application of our products. Any deviating agreements made by our employees that are not included in our datasheets will only be lawful providing they have been confirmed in writing by the management. Our raw materials, semi-finished products and products comply with the most stringent quality standards. This does not relieve the user of their responsibility to test our products prior to their application. Our general trading and delivery conditions, which we are happy to forward to you on demand, are and remain applicable at all times.
This specification sheet supersedes any previous versions.