Deys Betontechniek B.V.

Giet- en ondersabelingsmortels,Betonreparatie producten, Injectieproducten, Kunststoffen, Mortelpompen, Voegovergang constructies

Deys Targets
  • Chemical-and petrochemical plants

  • Delta works

  • Sea Lock IJmuiden

  • Harbours

  • Industry

  • Offshore

  • Powerplants

  • Department of public works

  • Railways

  • Utility

  • Airports

  • Water treatment

  • Road and water construction

  • windmills

    Windturbines

BETOCHEM 500

Description

BETOCHEM 500 is a transparent water dilutableA two-component impregnating substance which contains solvents, based on epoxy.
BETOCHEM has excellent impregnating capacity, is easy to process and shows very good adhesion.

Quality control

During manufacturing only raw materials of high quality are used which amply meet the strictest requirements. During the production process as well as during the final stages these materials are extensively tested for quality in our own laboratory.

Application areas
  • As a primer or coating for concrete and other cement-bound grounds
  • For dust-free finishing of cement-bound floors
Packaging and storage
2½, 5, 10 and 20 kg. In the original properly closed packaging in a cool dry place, frost free minimum storage life 6 months.
Precautions
Refer to the information on the packaging of the product, safety sheets and processing advice C.
Application
By means of brush, paint roller, air-spray and airless spray. Tools can be cleaned with BETOCHEM brush and spray dilutant EP.GroundConcrete and other cement-bound and stone-like grounds. The ground should be clean, dry and free of dust, grease and dirt, and furthermore should meet the terms and conditions which generally apply. Coating to mix with max of 20% water.
Ground
Concrete and other cement-bound and stone-like grounds. The ground should be clean, dry and free of dust, grease and dirt and furthermore should meet the terms and conditions which generally apply.
Resistance to chemicals
Refer to list of resistance to chemicals
Article Code500
Colourgrey or at request
Appearencesilky lustre
Density (kg/dm³)(20°C)1
Solid content (percentage by volume)40
Amount to be used [g/m²(dependent on ground)]approx. 250 (per layer)
Flash point [°C] (DIN 53213) 
 • Component A> 65
 • Component B> 65
Mixing ratio (by part of weight) 
 • Component A21
 • Component B79
Potlife [h] (20°C)approx. 1
Processing temp. [°C]5-35
Drying/full hardening [h] (20°C/65% RH) 
Dust-dryafter approx. 2 hours
Repaintableafter approx. 6 hours
Ready to be walked onafter approx. 16 hours
(in system building or with several layers, a maximum drying 
time of 24 hours between layers applies, 
unless a pre-treatment of the surface has occurred) 
Suggested System building:
BETOCHEM 500
BETOCHEM 2000 (coating, mix in sand if necessary)
BETOCHEM 2000 (coating, shine, matt and/or antiskid)
Heavy load
 
BETOCHEM 500 (2 layers)
* middle heavy load
Please contact us, we will send you the information.

Liability

The technical instructions and recommendations we provide on the basis of our experience and to the best of our knowledge, are entirely without obligation and merely provide an indication. Not all facts, problems and queries that occur during practical application can be included in a general documentation sheet. Our recommendations and instructions do not commit us to any legal obligations as a result of the purchase and application of our products. Any deviating agreements made by our employees that are not included in our datasheets will only be lawful providing they have been confirmed in writing by the management. Our raw materials, semi-finished products and products comply with the most stringent quality standards. This does not relieve the user of their responsibility to test our products prior to their application. Our general trading and delivery conditions, which we are happy to forward to you on demand, are and remain applicable at all times.
This specification sheet supersedes any previous versions.