Deys Betontechniek B.V.

Giet- en ondersabelingsmortels,Betonreparatie producten, Injectieproducten, Kunststoffen, Mortelpompen, Voegovergang constructies

Deys Targets

  • Chemical-and petrochemical plants

  • Delta works

  • Sea Lock IJmuiden

  • Harbours

  • Industry

  • Offshore

  • Powerplants

  • Department of public works

  • Railways

  • Utility

  • Airports

  • Water treatment

  • Road and water construction

  • windmills

    Windturbines

BETOCHEM 205 ADHESIVE

Description

BETOCHEM 205 a two-component primer free of solvents, based on epoxy.
ETOCHEM 205 is easy to process, has good adhesive strength and can be finished wet-in-wet with mortars based on epoxy resin.
BETOCHEM 205 has good penetrative qualities on porous grounds.

 
Quality control

During manufacturing only raw materials of high quality are used which amply meet the strictest requirements. During the production process as well as during the final stages these materials are extensively tested for quality in our own laboratory.
Application areas
  • BETOCHEM 205 Adhesive can be applied as adhesive layer to concrete and other stone-like grounds, specifically as a primer for Betec cement based products
  • As impregnation of concrete and brick-work to render them resistant to wear, water and chemicals and as active corrosion protection of reinforcement
  • When applied as adhesive primer, BETOCHEM 205 adhesive should be processed in combination with BETEC mortars WET-IN-WET; if the BETEC products cannot be applied within processing time, then spray in the primer within processing time and apply the BETEC products after approximately 18 hours.
Packaging and storage
1/2 kg (on request 1/4, 1, 2, 4 and 5 kg) – In the original properly closed packaging in a cool dry place, frost free minimum storage life 6 months.
Precautions
Refer to the information on the packaging of the product, safety sheets and processing advice C.
Application
By means of brush or paint roller. Tools can be cleaned with BETOCHEM brush dilutant EP.
Ground
Concrete and other cement-bound and stone-like grounds. The ground should be clean, dry and free of dust, grease and dirt and furthermore should meet the terms and conditions which generally apply.
Resistance to chemicals
Refer to list of resistance to chemicals
Article Code205 adhesive
Colouryellow
Appearanceshiny
Density [kg/dm³](20°C)1.0
Amount to be used [g/m²](at 250µm thickness of layer)250-500
Solid content (Vol %)100
Bond strength to concrete Higher than the tensile strength of concrete
Elongation break (%)5
Mixing ratio (by part of weight) 
 • Component A66
 • Component B34
Flash point [°C] (DIN 53213) 
 • Component A> 65
 • Component B> 65
Potlife [h] (20°C)approx. 40
Processing temperature [°C]10-35
Drying/full-hardening (h) (20°C/65% RH/250 mm thickness of layer) 
 • dust-dryafter approx. 8 hours
 • repaintableafter 12 hours
Please contact us, we will send you the information.

Liability

The technical instructions and recommendations we provide on the basis of our experience and to the best of our knowledge, are entirely without obligation and merely provide an indication. Not all facts, problems and queries that occur during practical application can be included in a general documentation sheet. Our recommendations and instructions do not commit us to any legal obligations as a result of the purchase and application of our products. Any deviating agreements made by our employees that are not included in our datasheets will only be lawful providing they have been confirmed in writing by the management. Our raw materials, semi-finished products and products comply with the most stringent quality standards. This does not relieve the user of their responsibility to test our products prior to their application. Our general trading and delivery conditions, which we are happy to forward to you on demand, are and remain applicable at all times.
This specification sheet supersedes any previous versions.