Deys Betontechniek Nederland BV
Gelreweg 5, 3843 AN Harderwijk
Postbus 330, 3840 AH Harderwijk
http://www.deys.nl

Telephone +31 (0)341 41 51 48
(24 hr / day)
Fax (0341) 42 54 90
info@deys.nl

General Processing Advice Moulding mortar (cement-bound) [A]

PDF/Print

Preliminary treatment of the ground
Before BETEC moulding mortar is applied, the mineral ground should be freed of cement skin, dirt, grease, oil, dust, curing compound, paint residues, loose parts and other contaminants.
The ground should be roughened to such a degree that a good adhesion will be obtained. Roughening and removing cement skin of the mineral ground can be done by mechanical means such as spraying water under high pressure, grit blasting, dabbing, grinding or hacking (pneumatically, electrically, manually).

The mineral ground should be frost-free!

Pre-moistening of the ground
Highly absorbing grounds must be moistened with clean tap water until no more water is absorbed in ample time before the moulding mortar is applied. When applying the moulding mortar the ground should not be water-repellent (glistening wet); this will reduce adhesion. If the ground still shows too much water absorption, the adhesive surface will burn because of the low water-cement ratio. 
There are various options for additional adhesive layers, dependent on the surface and field of application; refer to our technical staff concerning this.

Mixing
BETEC moulding mortars can be mixed in a free-fall concrete mixer, forced mixer, Deys 200 groutautomatic or in case of smaller amounts with a plaster mixer for electric drilling machines. For the correct water dosage we refer to the front of the packaging, the minimum and maximum water dosages are mentioned there. The water dosage must not be below the minimum need for water, the maximum dosage must not be exceeded.
Fill the mixer with 2/3 of the water dosage indicated, then add the BETEC moulding mortar.
First mix thoroughly, so that a mixture free of lumps is produced. Then gradually add the remaining 1/3 of the mixing water until the correct consistence is realised; do not add any more water than strictly necessary.

Processing
When applying moulding mortar it is always important to work from one side or angle, so that no air can be enclosed. Therefore see to it there are always enough vents. Furthermore, the moulding mortar should be poured in one continuous stream without interruptions; this will produce the best result. For special applications refer to our technical staff. In so far the construction to be grouted is not square, grouting must always take place from the longest side. Dependent upon the size of the grouting, a filling funnel can be used, so that the construction will be fully grouted because of the hydrostatic pressure.
When grouting large constructions, the use of fully automated mortar/conveyance pumps may be considered.

Curing
As BETEC moulding mortars are cement-bound materials, it is of the greatest importance that the mortar is cured. Because of the low water-cement ratio the mortar must be cured for 5 days at the minimum, in order to prevent premature desiccation and ensuing shrinkage. This can be done by wetting the mortar with clean tap water. Another option is covering the mortar with moist burlap covered with synthetic foil. Less time-consuming is the application of BETEC BETOFILM curing compound which must be applied in two layers.
Curing activities should be started as soon as possible, but at the latest after the mortar surface has started hardening.

Packaging and storage
BETEC mortars are delivered in packages of 20/25 kg; packaging consists of several layers of paper, with layers of perforated synthetic material in between. The packaging material is not water-tight and must be stored in a dry and frost-free place. In the original closed packaging the storage life of the mortar is 12 months.

Health & Safety
BETEC® are products based on cement and can therefore cause burns to skin and eyes, which should be protected during use. Wear gloves and protective eye shields. Wearing a dust mask is advised. Treat splashes to eyes and skin immediately with clean drinking water. Consult a doctor when irritation continues. If accidentally ingested, drink water and consult a doctor. Users must comply with all risk and safety phrases. Safety data sheets can be obtained from Deys Betontechniek or from our website. GISCODE ZP1.